High Resolution Automotive Oscilloscope – AHO1 Series
Bandwidth：200MHz
Sampling Rate：1GSa/s
Memory Depth：110Mpts
Analog Channels：4
Display：8 inches, 1280*800
Battery：built-in high-capacity Li-ion battery
One tool instead of two.
The AHO1 series is Micsig’s high-resolution automotive oscilloscope, built around a 12-bit ADC — 4096 quantization levels, 16 times a standard 8-bit automotive scope — so waveform detail on noisy vehicle signals stays visible instead of buried in quantization noise. A dual general-purpose / automotive software architecture covers dedicated engine, sensor and EV test modes, and a built-in 4⅚-digit multimeter runs alongside the scope with seamless switching, so there’s no second meter to carry. The whole unit is 3.1 cm thick, wrapped in a soft rubber protective casing, and runs on a high-capacity lithium-ion battery rated past 1000 charge cycles with USB-C and power-bank charging.
Eight reasons the AHO1 replaces two tools on the bench.
Each one solves a specific problem with carrying a separate scope and multimeter into mobile or outdoor repair work.
Built for ICE and EV
Automotive and general-purpose oscilloscope software in one unit, with dedicated engine, sensor and EV test modes.
Skip the second tool
A 4⅚-digit multimeter runs alongside the scope — voltage, current, resistance, continuity, diode and capacitance — with seamless switching.
See what 8-bit scopes miss
12-bit ADC, 4096 quantization levels — 16x a standard 8-bit automotive scope — for cleaner detail on noisy vehicle signals.
3.1 cm, full stop
An ultra-thin body in a soft rubber protective casing, built to go in a service bag, not stay on a bench.
A shift, not a session
High-capacity Li-ion battery rated past 1000 charge cycles, with USB-C and power-bank charging for a full day in the bay.
Multiple triggers, one capture
Standard segmented storage splits memory into segments so several trigger events land in one recording, reviewable individually or together.
However you want to run it
Full touchscreen, physical buttons and knobs, or a hybrid of both, on the SigTest UI.
Remote-ready
SCPI programmability, mobile app and PC control, plus direct HDMI output with no drivers to install.
Built for the vehicle systems that punish ordinary scopes.
From routine charging-circuit checks to CAN/LIN network debugging on both combustion and electric platforms, the AHO1 is sized and powered for mobile and outdoor diagnostic work.
- Charging & starting circuits
- Sensors and actuators
- Ignition systems
- CAN L/H, CAN FD and LIN networks
- FlexRay and K-line networks
- Combination / multi-bus tests
- ICE and EV / hybrid diagnostics
- Mobile and outdoor repair work
AHO14-200, in full.
The current AHO1 series configuration — full attenuator and accessory options available on request.
| Model | AHO14-200 |
|---|---|
| Bandwidth | 200 MHz |
| Analog Channels | 4 |
| Real-time Sampling Rate | 1 GSa/s |
| Rise Time | ≤ 1.75 ns |
| Memory Depth | 110 Mpts |
| Vertical Resolution | 12-bit |
| Max. Waveform Capture Rate | 50,000 wfms/s |
| Interfaces | USB 3.0 Host, USB Type-C, LAN, HDMI |
| Support Test | Charging/Start Circuits, Sensors, Actuators, Ignition, Networks (CAN L/H, CAN FD, LIN, Flexray, K-line), Combination Tests |
| Display | 8″ TFT LCD capacitive touchscreen, 1280×800 pixels |
| Battery | 3.7 V, 16,000 mAh lithium-ion battery |
| Charging | Standard DC 12V adapter; supports Type-C 5V charging |
| Multifunction Meter Accuracy | 4⅚ Digits |
| Dimension | 265 × 174 × 31 mm (W×H×Thickness) |
Documentation
Need to spec an automotive scope for your shop?
Pertech is Micsig’s authorized reseller in Israel. Tell us how many channels and which vehicle systems you’re testing, and we’ll confirm the right AHO1 configuration and accessory kit.
