Intel ISP Adaptor-C for EM100Pro and SF600 series – ISP-ADP-INTEL-C
Connect an EM100Pro or SF600 to Intel motherboards
The ISP-ADP-INTEL-C connects a DediProg EM100Pro, EM100Pro-G2, EM100Pro-G3, SF600, SF600Plus and SF600Plus-G2 to the 2×10 SPI flash programming header on Intel motherboards, so you can program or emulate the board’s SPI flash in-system. It supports Quad I/O.
It mates with Intel’s 2×10 connector (Samtec ASP-159358-02 or TFM-110-02-S-D-A) and comes on a cable about 8 cm long. The cable is soldered to the adaptor. When you remove it from the mainboard, pull on the adaptor, not on the cable. Apart from the cable, it works the same as the ISP-ADP-INTEL-C2.
Highlights
- Connects the EM100Pro, EM100Pro-G2, EM100Pro-G3, SF600, SF600Plus and SF600Plus-G2 to Intel motherboards
- Mates with the Intel 2×10 header (Samtec ASP-159358-02 or TFM-110-02-S-D-A)
- Cable about 8 cm long; soldered to the adaptor
- Quad I/O supported
Adaptor Pin-out (2×10)
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | KEY | 2 | CS0 |
| 3 | RESET | 4 | CS1 |
| 5 | GND | 6 | VCC |
| 7 | CLK | 8 | DQ2 / WP |
| 9 | DQ3 / HOLD | 10 | MISO |
| 11 | n/c | 12 | MOSI |
| 13-19 | n/c | 14-20 | n/c |
Signal Names: EM100Pro series / SF600 series ISP header (2×10) to Adaptor
A few signals carry different names on the programmer header and on the Intel adaptor. They map as follows.
| Programmer pin | Signal | Adaptor pin | Signal |
|---|---|---|---|
| 2 | CS2 | 4 | CS1 |
| 3 | CS1 | 2 | CS0 |
| 4 | VCC | 6 | VCC |
Which Intel ISP Adaptor Do I Need?
A, B and C models have the cable soldered to the adaptor; A2, B2 and C2 models have a detachable cable. Otherwise each pair is the same.
| Model | Use with | Design notes |
|---|---|---|
| ISP-ADP-INTEL-A / ISP-ADP-INTEL-A2 | SF100 | Pull-up resistors on WP and HOLD. Model A also has jumpers tying WP/HOLD to VCC, which can stop some mainboards from booting |
| ISP-ADP-INTEL-B / ISP-ADP-INTEL-B2 | SF600, SF600Plus, SF600Plus-G2 | Pull-up resistors on WP and HOLD. No Quad I/O |
| ISP-ADP-INTEL-C / ISP-ADP-INTEL-C2 | EM100Pro, EM100Pro-G2, EM100Pro-G3, SF600, SF600Plus, SF600Plus-G2 | No resistors or jumpers on any pin. Quad I/O supported. For single I/O programming, the target board needs pull-ups on WP/HOLD |
Key Specifications
| Spec | Value |
|---|---|
| Part number | ISP-ADP-INTEL-C |
| Use with | EM100Pro, EM100Pro-G2, EM100Pro-G3, SF600, SF600Plus and SF600Plus-G2 |
| Mates with | Intel 2×10 header, Samtec ASP-159358-02 or TFM-110-02-S-D-A |
| Cable | About 8 cm, soldered to the adaptor |
| Quad I/O | Yes |
| Design notes | No resistors or jumpers on any pin, to keep the signal path clean. For single I/O programming, the target board needs pull-up resistors on WP and HOLD. |
In the Box
- ISP-ADP-INTEL-C adaptor with cable
For the programmer, see the EM100Pro-G3 and SF600Plus-G2.
For quantities, lead time or a quote, contact Pertech.
