Intel ISP Adaptor-B2 for SF600 series – ISP-ADP-INTEL-B2
Connect the SF600 series to Intel motherboards
The ISP-ADP-INTEL-B2 connects a DediProg SF600, SF600Plus and SF600Plus-G2 to the 2×10 SPI flash programming header on Intel motherboards, so you can program or emulate the board’s SPI flash in-system. It does not support Quad I/O; for Quad I/O, use the ISP-ADP-INTEL-C2.
It mates with Intel’s 2×10 connector (Samtec ASP-159358-03) and comes on a cable about 8 cm long. The cable plugs into the adaptor through a connector, so you can detach it from the adaptor. Apart from the cable, it works the same as the ISP-ADP-INTEL-B.
Highlights
- Connects the SF600, SF600Plus and SF600Plus-G2 to Intel motherboards
- Mates with the Intel 2×10 header (Samtec ASP-159358-03)
- Cable about 8 cm long; detachable from the adaptor
- No Quad I/O
Adaptor Pin-out (2×10)
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | KEY | 2 | CS0 |
| 3 | RESET | 4 | CS1 |
| 5 | GND | 6 | VCC |
| 7 | CLK | 8 | DQ2 / WP |
| 9 | DQ3 / HOLD | 10 | MISO |
| 11 | n/c | 12 | MOSI |
| 13-19 | n/c | 14-20 | n/c |
Signal Names: SF600 / SF600Plus / SF600Plus-G2 ISP header (2×10) to Adaptor
A few signals carry different names on the programmer header and on the Intel adaptor. They map as follows.
| Programmer pin | Signal | Adaptor pin | Signal |
|---|---|---|---|
| 2 | CS2 | 4 | CS1 |
| 3 | CS1 | 2 | CS0 |
| 4 | VCC | 6 | VCC |
Which Intel ISP Adaptor Do I Need?
A, B and C models have the cable soldered to the adaptor; A2, B2 and C2 models have a detachable cable. Otherwise each pair is the same.
| Model | Use with | Design notes |
|---|---|---|
| ISP-ADP-INTEL-A / ISP-ADP-INTEL-A2 | SF100 | Pull-up resistors on WP and HOLD. Model A also has jumpers tying WP/HOLD to VCC, which can stop some mainboards from booting |
| ISP-ADP-INTEL-B / ISP-ADP-INTEL-B2 | SF600, SF600Plus, SF600Plus-G2 | Pull-up resistors on WP and HOLD. No Quad I/O |
| ISP-ADP-INTEL-C / ISP-ADP-INTEL-C2 | EM100Pro, EM100Pro-G2, EM100Pro-G3, SF600, SF600Plus, SF600Plus-G2 | No resistors or jumpers on any pin. Quad I/O supported. For single I/O programming, the target board needs pull-ups on WP/HOLD |
Key Specifications
| Spec | Value |
|---|---|
| Part number | ISP-ADP-INTEL-B2 |
| Use with | SF600, SF600Plus and SF600Plus-G2 |
| Mates with | Intel 2×10 header, Samtec ASP-159358-03 |
| Cable | About 8 cm, detachable (connector at the adaptor) |
| Quad I/O | No |
| Design notes | Pull-up resistors on WP and HOLD. |
In the Box
- ISP-ADP-INTEL-B2 adaptor with cable
For the programmer, see the SF600Plus-G2 programmer.
For quantities, lead time or a quote, contact Pertech.
