Intel ISP Adaptor-B for SF600 series – ISP-ADP-INTEL-B
Connect the SF600 series to Intel motherboards
The ISP-ADP-INTEL-B connects a DediProg SF600, SF600Plus and SF600Plus-G2 to the 2×10 SPI flash programming header on Intel motherboards, so you can program or emulate the board’s SPI flash in-system. It does not support Quad I/O; for Quad I/O, use the ISP-ADP-INTEL-C.
It mates with Intel’s 2×10 connector (Samtec ASP-159358-03) and comes on a cable about 8 cm long. The cable is soldered to the adaptor. When you remove it from the mainboard, pull on the adaptor, not on the cable. Apart from the cable, it works the same as the ISP-ADP-INTEL-B2.
Highlights
- Connects the SF600, SF600Plus and SF600Plus-G2 to Intel motherboards
- Mates with the Intel 2×10 header (Samtec ASP-159358-03)
- Cable about 8 cm long; soldered to the adaptor
- No Quad I/O
Adaptor Pin-out (2×10)
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | KEY | 2 | CS0 |
| 3 | RESET | 4 | CS1 |
| 5 | GND | 6 | VCC |
| 7 | CLK | 8 | DQ2 / WP |
| 9 | DQ3 / HOLD | 10 | MISO |
| 11 | n/c | 12 | MOSI |
| 13-19 | n/c | 14-20 | n/c |
Signal Names: SF600 / SF600Plus / SF600Plus-G2 ISP header (2×10) to Adaptor
A few signals carry different names on the programmer header and on the Intel adaptor. They map as follows.
| Programmer pin | Signal | Adaptor pin | Signal |
|---|---|---|---|
| 2 | CS2 | 4 | CS1 |
| 3 | CS1 | 2 | CS0 |
| 4 | VCC | 6 | VCC |
Which Intel ISP Adaptor Do I Need?
A, B and C models have the cable soldered to the adaptor; A2, B2 and C2 models have a detachable cable. Otherwise each pair is the same.
| Model | Use with | Design notes |
|---|---|---|
| ISP-ADP-INTEL-A / ISP-ADP-INTEL-A2 | SF100 | Pull-up resistors on WP and HOLD. Model A also has jumpers tying WP/HOLD to VCC, which can stop some mainboards from booting |
| ISP-ADP-INTEL-B / ISP-ADP-INTEL-B2 | SF600, SF600Plus, SF600Plus-G2 | Pull-up resistors on WP and HOLD. No Quad I/O |
| ISP-ADP-INTEL-C / ISP-ADP-INTEL-C2 | EM100Pro, EM100Pro-G2, EM100Pro-G3, SF600, SF600Plus, SF600Plus-G2 | No resistors or jumpers on any pin. Quad I/O supported. For single I/O programming, the target board needs pull-ups on WP/HOLD |
Key Specifications
| Spec | Value |
|---|---|
| Part number | ISP-ADP-INTEL-B |
| Use with | SF600, SF600Plus and SF600Plus-G2 |
| Mates with | Intel 2×10 header, Samtec ASP-159358-03 |
| Cable | About 8 cm, soldered to the adaptor |
| Quad I/O | No |
| Design notes | Pull-up resistors on WP and HOLD. |
In the Box
- ISP-ADP-INTEL-B adaptor with cable
For the programmer, see the SF600Plus-G2 programmer.
For quantities, lead time or a quote, contact Pertech.
