Ronetix iMX8M-CM is a System-on-Module on a standard SO-DIMM 204 card (67.6 x 40 mm) built on the NXP i.MX8M (Quad): four Arm Cortex-A53 cores at 1.5 GHz, a 266 MHz Cortex-M4 co-processor and 3D graphics. It is the multimedia module of the SO-DIMM range, with HDMI, two MIPI-CSI cameras, two PCIe lanes and two USB 3.0 ports. Ronetix sells it alone or with the i.MX8M-MB base board as a starter kit. Pertech is a Ronetix distributor.
iMX8M-CM highlights
- NXP i.MX8M: 4x Arm Cortex-A53 at 1.5 GHz plus Cortex-M4 at 266 MHz
- 3D graphics; NEON SIMD and VFPv4
- HDMI, LVDS up to 1400 x 1050 at 60 Hz and MIPI-DSI
- 2x MIPI-CSI 4-lane cameras
- 2x PCIe x1 Gen 2.1 and 2x USB 3.0/2.0 OTG
- 1 GiB LPDDR4 (up to 4 GiB), 4 GiB eMMC (up to 64 GiB)
- WM8960 audio codec; optional 2×2 MIMO Wi-Fi 802.11ac and Bluetooth 5.0
Where the iMX8M-CM fits
- Multimedia and HDMI display products
- Dual-camera devices
- Gateways that need PCIe and USB 3.0 expansion
- Teams starting from the i.MX8M starter kit
Key Specifications
| Spec | Value |
|---|---|
| Model | iMX8M-CM |
| Form factor | SO-DIMM 204 (JEDEC MO-274), 67.6 x 40 mm |
| Processor | NXP i.MX8M: 4x Cortex-A53 1.5 GHz, Cortex-M4 266 MHz |
| Memory | 1 GiB LPDDR4 (up to 4 GiB); 4 GiB eMMC (up to 64 GiB); 64 KiB I2C EEPROM and 64 MiB QSPI NOR optional |
| Display | HDMI, LVDS up to 1400 x 1050 at 60 Hz, MIPI-DSI |
| Camera | 2x MIPI-CSI, 4 lanes |
| Network | Gigabit Ethernet; Wi-Fi 802.11ac 2×2 MIMO and Bluetooth 5.0 optional |
| Audio | WM8960 codec: stereo headphone, 1 W class D speaker, microphone |
| I/O | 2x PCIe x1 Gen 2.1, 2x USB 3.0/2.0 OTG, up to 4x UART, SD/SDIO, up to 3x SPI, up to 3x I2C, up to 4x PWM, GPIO |
| Supply | 3.5 to 4.5 V |
| Operating temperature | 0 to +70 °C; -40 to +85 °C optional |
| Relative humidity | 10% to 90% |
| MTTF | More than 200,000 hours |
Frequently asked questions
What is the iMX8M-CM?
It is a Ronetix System-on-Module on an SO-DIMM 204 card with the NXP i.MX8M processor, HDMI and two MIPI-CSI cameras.
Is there a starter kit?
Yes. The Starter Kit i.MX8M combines this module with the i.MX8M-MB base board, a power supply and an SD card with Yocto pre-installed.
What supply voltage does it need?
Ronetix specifies 3.5 to 4.5 V for this module.
Where can I buy the iMX8M-CM in Israel?
Pertech is a Ronetix distributor in Israel. Contact Pertech for a quote, lead time, memory and temperature options, or help choosing a module and carrier board.
Related Ronetix products at Pertech
- Starter Kit i.MX8M
- iMX8M-MINI-CM SoM with NXP i.MX8M Mini
- iMX8M-NANO-CM SoM with NXP i.MX8M Nano
- PEEDI JTAG/SWD/BDM Emulator and Flash Programmer
- Ronetix products at Pertech
Building an HDMI or dual-camera device? Contact Pertech for a quote, availability or help choosing the right module.
